Simplest FM Transmitter S8050

This is the simplest fm transmitter circuit you can ever find on internet,because so many “simple transmitters” (they call it simple but many of them don’t work!) on internet will not work as those circuits are designed poorly. i had built around 100s of transmitters in the past and most of them were built successfully, because the design is just cool and reliable. This circuit is for those who have built many fm transmitters without any sign of working!, so try this one and i am sure you can make it!.

An Fm transmitter is a circuit/device to transmit audio signals to an fm radio receiver through air (wirelessly). The input (audio)to an fm transmitter can be fed using a microphone or the output of your music player to be transmitted, and the signal which you transmit can be received using an FM radio, the advantages of FM TRANSMITTERS ARE many:

1.You may transmit audio to another room/floor of your house without using any wires!

2.You may transmit your own voice if you used an electret microphone in the circuit

3.You don’t need to build a receiver to receive the ransmitting audio as any standard fm radio can be used to receive your voice/audio and many..!

this circuit can transmit audio to a distance of around 50 meters if you used 2n3904 transistor and boost the supply voltage to 6V, and 1Km(1 kilometer) if used S8050 transistor with 9V supply!

Components you need

R1 – 47K resistor

R2 – 100 ohms resistor

C1 – 22n none polarised capacitor

C2 – 1n none polarised capacitor

C3 – 4.7pf none polarised capacitor

c4 – 22n none polarised capacitor

T1 – Transistor BC547(short range),2N3904(medium range,recommended),S8050(long range)

VC1 – 22pf Variable trimmer capacitor (trimcap)

L1 – Aircore inductor, 6turns on a 3mm dia former eg.Wind over a pen refill.

Antenna – a short length wire

3V battery (Use only battery)

Good quality pcb or veroboard. (breadboards may not work)

after building is done,power the circuit using a 3V battery and connect any audio source to “audio input” pin properly, set an fm radio minimum 3 meters away. Start tuning the radio and tuning the VC1 at the same time untill you receive the transmitting audio, if you can hear the audio then you are DONE!.


1.All components in the circuit is not intended to change their values

2.Using correct value components in the circuit is vital

3.If the transmitting audio is too loud and unclear, then add a 100K or 1 Mega ohm resistor across the audio input pin, the value of this resistor depends on how much powerful you audio signal is and should be selected untill you get a very clear voice.


  1. ساجرب وارد عليكم

  2. انا نفذت واحدة كهذة مشابهة لها عملت الملف 6 لفات لم تعمل الاقصرته الى 4 وباعدت بينهم اشتغلت تمام

  3. If you look at the PCB board you will see that he left out the four diodes in the schematic and the parts list.

    1. Anonymous25/5/20 00:32

      it is for using a transformer instead of battery, diodes for rectifying

  4. Really, I enjoy your site with effective and useful information. fm transmitter supplier in India

  5. replacement VC1 by ceramic capacitor

  6. A 2-channel one is more flexible, but cannot control other features. For example, a 4-channel transmitter isn't a good choice for a drone, as it only supports a single channel, which is too basic for a small drone. Find more interesting information about best quadcopter drone transmitter for fpv / non fpv drones (updated 2020) here.

  7. Anonymous4/5/24 17:53

    What are these 22n none polarized